Article marked

Error occurred Please try again later

AIRSTOP KB Adhesive Tape

AIRSTOP KB Adhesive Tape

Tear-resistant adhesive tape for airtight sealing. With an exceptionally age-resistant adhesive layer. It is suitable for use on almost all surfaces. Ideally suitable for linear joints.

Working temperature: from -5 °C

Product data sheet

Available dimensions
Product data
Processing guideline
Downloads

AIRSTOP KB Adhesive Tape

Available dimensions
Product data
Processing guideline
Downloads

Available dimensions

Article number	Roll width	Roll length	Carton
3AKB50	50 mm	50 m	8 rolls
3AKB60	60 mm	50 m	8 rolls
3AKB100	100 mm	50 m	4 rolls
3AKB150	150 mm	50 m	2 rolls
3AKB200	200 mm	50 m	2 rolls

Show Inquiry List

Product data

Field of application

adhesion of vapour retarders and airtight layers
joins of OSB and DWD (wood fibre board) panels, indoors and outdoors
joins and connections with wood, OSB, metal...
for adhesion to masonry use a primer if necessary
joint connections according to ÖNORM B 5320 and DIN 4108-7 are possible

Advantages

tear-resistant
high adhesion

To guarantee air and wind-tightness for the skin of a construction it must have the appropriate foils or panel materials providing a permanent seal at overlaps, gaps, joints and penetration points. AIRSTOP Adhesive Tape is tear-resistant with adhesive generously applied and is suitable for a variety of bonding applications.

Material composition

Tear-resistant system adhesive tape with acrylate adhesive

Thickness

0.3 mm

Colour

White with AIRSTOP imprint

Temperature resistance

-40 °C

Temperature resistance

100 °C

UV-resistance

2 months

Processing guideline

DESCRIPTION

Tear resistant system adhesive tapes with acrylate adhesive.

UV STABILITY

Max. 2 months; for higher requirements please use the OMEGA UVKB Facade tape or AIRSTOP ULTRA Tape.

ADHESIVE FORCE

AIRSTOP adhesive tapes perform the function of airtight and wind-tight sealing and not that of positive bonding. Vapour barriers and other films must always be secured by staples, laths or the like (mechanical).

PLASTERING OVER

AIRSTOP KB Adhesive tape cannot be plastered or painted over. Please use the AIRSTOP FLEX adhesive tape for this application.

BONDING TECHNIQUE

When affixing the adhesive tape, the tape must be adhered over its entire surface to the substrate. The higher the contact pressure, the better the adhesion (AIRSTOP ROLL Pressing Roller, AIRSTOP RAK Plastic Squeegee). It is possible without problem to adhere the tape over itself or to adhere it crosswise. We recommend the AIRSTOP SPRINT Sealant or AIRSTOP DIMAROLL for plastered surfaces or very rough wood. The materials to be processed must be free of dust and grease, in addition to which the substrates must be dry and capable of bearing loads. In the case of doubt we recommend the pre-treatment of the substrate. (UNI Primer or BUBI LF Adhesive Primer).

BONDING AT VERY LOW TEMPERATURES

AIRSTOP adhesive tapes are suitable for bonding from approx. –5 °C. Note please that surface condensate can result at lower temperatures even in the case of minimal changes in temperature. This acts like a separating layer and decreases the adhesion. Hot-stored tapes provide noticeably improved initial adhesion. (fan heaters, insulated containers)

ADHERES TO THE FOLLOWING SUBSTRATES

Wood, wood-based panels (OSB, MDF, 3S-panels etc.), brick, plastics (smooth surface, free of silicones and waxes), metals free of oxides and rust etc.
Observe the system suggestions in accordance with our price list.

BONDING TIME

After the attachment of the AIRSTOP adhesive tape a so-called 'cross-linking process' takes place. This takes about 6 - 24 hours, depending on the temperature. Only then is the full adhesion attained.

REMOVAL OF THE ADHESIVE TAPE

Warm up the adhesive tape with a hair dryer and pull slowly on the adhesive tape. Remove the last residues with AIRSTOP ADC adhesive cleaner. Caution: do not rub for too long in one place on sensitive substrates. If necessary, wait 5 - 15 minutes and spray AIRSTOP ADC adhesive cleaner on once again and wipe it off.

STORAGE

Cool and dry in a closed cardboard box; do not stack rollers on top of one another without release paper in between.

DISPOSAL

Release paper and adhesive tape - domestic waste, waste tip

GUARANTEE

The acrylate adhesive employed does not contain any additives that cause the adhesive layer to become brittle and is therefore extremely resistant to aging.

Instructions

DESCRIPTION

Tear resistant system adhesive tapes with acrylate adhesive.

UV STABILITY

Max. 2 months; for higher requirements please use the OMEGA UVKB Facade tape or AIRSTOP ULTRA Tape.

ADHESIVE FORCE

PLASTERING OVER

AIRSTOP KB Adhesive tape cannot be plastered or painted over. Please use the AIRSTOP FLEX adhesive tape for this application.

BONDING TECHNIQUE

BONDING AT VERY LOW TEMPERATURES

ADHERES TO THE FOLLOWING SUBSTRATES

BONDING TIME

REMOVAL OF THE ADHESIVE TAPE

STORAGE

Cool and dry in a closed cardboard box; do not stack rollers on top of one another without release paper in between.

DISPOSAL

Release paper and adhesive tape - domestic waste, waste tip

GUARANTEE

The acrylate adhesive employed does not contain any additives that cause the adhesive layer to become brittle and is therefore extremely resistant to aging.

Downloads

Product data sheet Product data sheet pdf 777 KB

Downloads

Documents