OMEGA UVKB Facade Tape

OMEGA UVKB Facade Tape

UV-resistant adhesive tape for sealing in and around facades.
Working temperature: from -5 °C

Suitable for G20/G50
Permanently UV-resistant
Highly water-resistant adhesive

Product data sheet

Available dimensions
Product data
Processing guideline
Downloads

Available dimensions
Product data
Processing guideline
Downloads

Available dimensions

Article number	Roll width	Roll length	Split liner	Carton
3OMFA53	53 mm	25 m	-	8 rolls
3OMFA60	60 mm	25 m	-	8 rolls
3OMFA100	100 mm	25 m	-	4 rolls
3OMFA100G	100 mm	25 m	40 / 60	4 rolls

Show Inquiry List

Product data

Field of application

for seals at overlaps, gaps and penetration points of membranes or boarding
system adhesive tape for OMEGA G20 and G50 facade membrane
indoor use possible
optimised for demanding outdoor use

Advantages

tear-resistant
strong adhesion
permanent UV-resistance
highly water-resistant adhesive

To guarantee air and wind-tightness for the skin of a construction it must have the appropriate foils or panel materials providing a permanent seal at overlaps, gaps, joints and penetration points. OMEGA Facade Tape is permanently UV-resistant, tear-resistant with adhesive generously applied and is suitable for a variety of bonding applications.

Material composition: Tear-resistant system adhesive tape with acrylate adhesive. Base material has a permanently UV- resistant coating

Thickness: 0.5 mm

Temperature resistance: -40–100 °C

Working temperature: -5–40 °C

Shelf life: 2 years

Colour: Black

Processing guideline

DESCRIPTION

Colour-coordinated and technically matched, permanently UV-resistant system adhesive tape for butt and flashing bonding of OMEGA G20 and OMEGA G50 facade membrane with maximum water-resistant polyacrylate adhesive for safe outdoor use.

ADHESIVE STRENGTH

AIRSTOP adhesive tapes perform the function of airtight and wind-tight sealing. Storm load or insulation weight cannot be permanently absorbed by the tape. Vapor barriers and facade membrane must always be mechanically secured with staples (concealed behind the overlap) and battens.

BONDING TECHNIQUE

OMEGA UVKB facade tape must be pressed onto the substrate over the entire surface. Folds or waves in membrane or tape, open to the top, are not permitted. The higher the contact pressure, the faster the final strength develops. Sticking the tape on itself is possible without any problems. Do not stretch during application. The AIRSTOP ROLL pressing roller helps to prevent tensile stresses during pressing. For bonding outside corners and exterior edges (convex), we recommend the 100 mm size with backing strip separation (40/60) due to the inherent rigidity of the substrate. No side should show less than 40 mm of adhesive surface.
All materials must be free of dust and grease, and the substrate must be dry and load-bearing before use. In the case of sandy or rough substrates, concrete and low temperatures, the adhesion of the substrate can be significantly improved with UNI SPRAY Primer.

OMEGA adhesive tapes are suitable for bonding from approx. -5°C. Note please that surface condensate can result at lower temperatures even in the case of minimal changes in temperature. This acts like a separating layer and decreases the adhesion. Tapes stored in warm conditions provide noticeably improved initial adhesion (20-30°C, fan heater, insulated container, construction hut).

SUBSTRATES

OMEGA G20 and OMEGA G50 facade membranes, OMEGA WD wind seal, ISOCELL vapor barriers as well as wood, wood-based panels (OSB, MDF, 3S panels), bricks, plastics (PP, PE, PA, smooth surfaces, free of silicones and waxes), metals free of oxides/rust.

BONDING TIME

A ”cross-linking process” takes place after the attachment of the AIRSTOP adhesive tape. This takes about 6 - 24 hours, depending on the temperature. The final strength on G20 and G50 facade membranes can also be increased.