Article marked
Error occurred Please try again later
Back to overview

OMEGA DRAINY PLUS Roof Underlay

OMEGA DRAINY PLUS Roof Underlay
An extremely diffusive roof underlay designed for use under metal covering. It is equipped with 3-dimensional polypropylene mesh fabric and is laid directly on the wood sheathing. The mesh fabric protects the sheeting from heat and damage from the metal and guarantees that the underlay is ventilated from above.
  • FOR METAL ROOFING

Available dimensions

Article number Type Roll width Roll length Rolls / Pallet Total area Inquiry List
2QDRAINPL PLUS 1.5 m 25 m 10 rolls 375 m²

Field of application

  • especially for use under metal covering
  • for vented pitched roofs
  • high quality protection for wood and insulation
  • installation directly on the thermal insulation or wood sheathing

Advantages

  • rain-tight
  • wind-tight
  • uv-stability
  • 100% recyclable
  • non-glare
  • anti-slip

Product data

An extremely diffusive roof underlay designed for use under metal covering. It is equipped with 3-dimensional polypropylene mesh fabric and is laid directly on the wood sheathing. The mesh fabric protects the sheeting from heat and damage from the metal and guarantees that the underlay is ventilated from above.
Material composition
3-layer PP fleece with 3-dimensional PP mesh fabric
Thickness
mesh fabric 7,5 mm
Thickness
0.75 mm
Colour
Light grey fleece / black mesh fabric
Weight
450 g/m²
Weight per unit area
(± 5 %)
sd-value
0.02 m
Temperature resistance
-20 °C
Temperature resistance
100 °C
UV-resistance
3 months
Resistance to water flow
W1
Resistance to water flow
EN 1928
Elongation - lengthwise
50 - 60 %
Elongation - crosswise
50 - 60 %
Elongation
EN 12311-1
Tensile strength - lengthwise
295 (± 40) N / 50 mm
Tensile strength - crosswise
205 (± 40) N / 50 mm
Tensile strength
EN 12311 - 1
Tear propagation resistance - lengthwise
185 (± 30) N
Tear propagation resistance - crosswise
230 (± 30) N
Tear propagation resistance
EN 12310-1
Storage
cool and dry
Fire performance
E
Fire performance
EN 13501_1 / EN 11925_2

Processing guideline

(1) SEPARATING LAYER BELOW THE METAL SHEET

OMEGA DRAINY Roof Underlay is installed parallel to the eaves on boarding. The sections are nailed and concealed on the side facing the roof ridge at the overlap (marked edge). Where overlaps are necessary, such as vertical edges, penetration points, valleys and dormer windows the fabric is removed over a width of 10cm at the overlap. The overlaps are glued with OMEGA QUILLI Sealing Compound or joined using the integrated adhesive strip.
When installing OMEGA DRAINY Roof Underlay it is important to have a clean substrate as otherwise the highly breathable membrane can be damaged mechanically and no liability can be accepted on the part of the manufacturer. Any damage that occurs must be remedied immediately.
(1) SEPARATING LAYER BELOW THE METAL SHEET

(2) EAVES CONSTRUCTION

We recommend drainage using a metal section.
(2) EAVES CONSTRUCTION

(3) PENETRATION POINTS

Openings where the roof is penetrated (outlet vents, roof windows, chimneys etc.) should be kept as small as possible and the membrane sections should be attached in such a way that no rain or snow can enter. The seal must be made with sealing tape and sleeves from ISOCELL GmbH & Co KG.
Make sure that the substrate is clean! The manufacturer can accept no liability for mechanical damage. The applicable regulations and guidelines (e.g. of the ZVDH (Central Association of German Roofers) for Germany, Austrian Standard, ÖNORM B 4119, for Austria, ...) must be observed!
The impermeability of micro-porous webs can be impaired by wood preservatives, chainsaw oil or oily substances. Our application technicians will be glad to inform you!
The OMEGA DRAINY does not replace roof covering. The roof must be covered at least 2 months after installation of the OMEGA DRAINY.
If the roof is not covered immediately after installation of the membrane, the section must be fixed mechanically.
(3) PENETRATION POINTS