Article marked
Error occurred Please try again later
Back to overview

OMEGA 180 SK DUO Roof Underlay

OMEGA 180 SK DUO Roof Underlay
Vapour permeable roof underlay for installation directly onto the face of the thermal insulation or wood sheathing. 3-layer fleece combination.
  • NON-SLIP AND TEAR RESISTANT SURFACE

Available dimensions

Article number Type Roll width Roll length Rolls / Pallet Total area Inquiry List
2OMEGA Standard 1.5 m 50 m 20 rolls 1500 m²
2OMEGA25 Standard 2.5 m 50 m 20 rolls 2500 m²
2OMEGA3 Standard 3 m 50 m 20 rolls 3000 m²
2OMEGASKWS SK DUO 1.5 m 50 m 20 rolls 1500 m²

Field of application

  • for vented pitched roofs
  • high quality protection for wood and insulation
  • for installation directly on thermal insulation or wood sheathing

Advantages

  • rain-tight, wind-tight
  • uv-stabilized
  • 100% recyclable
  • easy to cut
  • anti-glare
  • anti-slip

Product data

is an extremely diffusive underlay with two two-way acrylate adhesive strips for installation directly on the thermal insulation or the wood sheathing. Raintightness proved by Holzforschung Austria. (Report no. : 301/2003/2-T/HH).
Material composition
3-layer PP fleece with two two-way acrylate adhesive strips
Thickness
0.72 mm
Colour
Grey
Weight
180 g/m²
Weight per unit area
(±10)
sd-value
0.025 m
sd-value
(+ 0,035 / - 0,01)
Temperature resistance
-40 °C
Temperature resistance
80 °C
Temperature resistance
(short-term 100 °C)
UV-resistance
4 weeks
Resistance to water flow
W1
Resistance to water flow
EN 1928
Elongation - lengthwise
35 - 70 %
Elongation - crosswise
50 - 90 %
Elongation
EN 12311-2
Tensile strength - lengthwise
370 (-60) N / 50 mm
Tensile strength - crosswise
260 (-50) N / 50 mm
Tensile strength
EN 12311-2
Tear propagation resistance - lengthwise
230 (- 50) N
Tear propagation resistance - crosswise
230 (- 50) N
Tear propagation resistance
EN 12310-1
Storage
cool and dry
Fire performance
E
Fire performance
EN 13501_1 / EN 11925_2

Processing guideline

(1) UNDERLAY (unsupported)

OMEGA roof Underlay is nailed parallel to the eaves with a slight drape and laid and mechanically fixed above the rafters. Vertical overlaps/joins must always lie on a rafter.
All overlaps must be bonded with OMEGA QUILLI Sealing Compound. Horizontal underlay panels can be joined using SK DUO adhesion as provided or with OMEGA QUILLI Sealing Compound. (no pressure need be applied).
(1) UNDERLAY (unsupported)

(2) UNDERLAY (supported)

OMEGA roof underlay is laid on sheathing parallel to the eaves. The blankets are fixed with concealed nails spaced at 10 cm at the ridge-side edges (marks at edge). All overlaps/joins must be bonded with OMEGA QUILLI Sealing Compound (without applying pressure) or the integrated adhesive strips (applying adequate pressure). For the raintight version (temporary cover) a nail-seal under the counter batten (OMEGA QUILLI Sealing Compound or OMEGA NDB Nail Sealing Tape ) is necessary. The single-sided nail-seal tape must be attached to the roof underlay directly beneath the counter batten!
(2) UNDERLAY (supported)

(3) EAVES CONSTRUCTION

We recommend an eaves construction with drainage below the gutter so that snowmelt build-up can easily drain off. We recommend the use of a metal sheet to drain off water.
(3) EAVES CONSTRUCTION

(4) RIDGE AREA

The ridge area is closed directly when covered with OMEGA roof underlay. This provides immediate protection against water penetration. In non-insulated lofts and/or ventilated interior insulation the ridge formation must be made open: the blankets end 3 cm before the ridge apex, counter battens are mounted and a
50 cm wide strip of OMEGA roof underlay must be attached over the roof apex.
(4) RIDGE AREA

(5) VALLEY INFORMATION

The first step in valley formation is to lay a continuous valley blanket.
(5) VALLEY INFORMATION

(6) PENETRATIONS

Sections cut out for roof penetrations (extractor pipes, roof windows, chimneys, etc.) should be kept as small as possible and the ends of the sheets must be fixed so that no rain or snow can penetrate. To achieve a perfect seal the suitable adhesive technology by ISOCELL GmbH & Co KG must be used.
Make sure that the substrate is clean! The manufacturer can accept no liability for mechanical damage. The applicable regulations and guidelines (e.g. of the ZVDH (Central Association of German Roofers) for Germany, Austrian Standard, ÖNORM B 4119, for Austria, ...) must be observed!
The impermeability of micro-porous webs can be impaired by wood preservatives, chainsaw oil or oily substances. Our application technicians will be glad to inform you!
The roof underlay does not replace roof covering. The roof must be covered during the period of the specified weathering time. Early covering has a positive effect on the resistance to ageing.
(6) PENETRATIONS